ADVIA Centaur® XPT System Calibration Online Training

Existem várias partes principais de um sistema SPECT/CT. Selecione o pop-up para saber mais sobre os principais componentes. Welcome to the ADVIA Centaur® XPT System Calibration Online Training course. Calibration is required when a new lot of reagent is added to the system and when the calibration interval expires. We will discuss the required steps to order and review calibrations in this course. Select Next to review the course objectives. Describe the process required to review calibration status Discuss the accept option Identify the steps required to scan Master Curve and Test Definition (MC DEF) cards and Calibrator Definition cards List the steps required to order a calibration Review the calibration data Upon successful completion of this course you will be able to: Select Next to continue. Antes que uma aquisição possa ser realizada, um paciente deve ser registrado no banco de dados. Existem três maneiras de registrar um paciente: O registro manual, o registro de um paciente já existente ou o registro de um paciente a partir do HIS/RIS. Congratulations.  You have completed the ADVIA Centaur® XPT System Calibration Online Training course.  Listed below are the key points that have been presented.  Take time to review the material before you proceed to the final quiz. Describe the process required to review calibration status Screens used to review calibration status: Calibration Summary - provides calibration status for all tests Reagent Status - lists detailed status information for onboard reagents, including calibration status The overall calibration status messages are: Current Calibration Due to Expire Expired No Calibrator Definition No Master Curve Not Calibrated Waived Identify the steps required to scan Master Curve and Test Definition (MC DEF) cards and Calibrator Definition cards Calibrator Definition Cards Located in the calibrator kit Must be scanned with every new calibration lot Can be scanned at any time Must be scanned at the Calibrator Definitions screen To scan a Calibrator Definition card: Locate the Calibrator Definition card Open the Calibrator Definitions screen Select Add Calibrator Definition Scan the Calibrator Definition card Check the calibrator values Select Save Master Curve and Test Definition (MC DEF) Cards Located in the reagent kit Must be scanned with every new reagent lot Can have two or more 2D barcode squares Can only be scanned if the system is in Ready Can be scanned from any window location To scan an MC DEF card: Locate the MC DEF card Scan the first 2D barcode Scan the second 2D barcode Scan the remaining 2D barcodes (if applicable) Select Save List the steps required to order a calibration Calibrate an assay when: The calibration interval expires A calibration is invalid A new lot of assay reagent is used Controls are repeatedly out of range Note: Refer to the Instructions for Use (IFU) for calibrator preparation and storage requirements. To manually create a calibration order: At the Command Bar, select Calibration Select the Calibration Order tab Select a test Select a reagent lot Select a calibrator lot Select Save The system can be configured to automatically create a calibration order when calibration samples are loaded on the system. To configure automatic calibration ordering: Select Setup from the Command Bar Select the System Configuration tab Select System Settings Enable the Automatic Calibration Order Settings Review the calibration data The ADVIA Centaur XPT system uses a two-point calibration system: Uses low and high calibrators Eliminates the need to measure a full standard curve or calibrate every time the assay is performed Screens used to review calibration data: Calibration Results Overview: "Valid" indicates that the Calibration Evaluation Criteria have passed Calibration Summary: "Current Calibration" indicates that the Calibration Evaluation Criteria have passed Discuss the accept option Accepting a Calibration: Required when the calibration status is "Pending Accept" status on the Calibration Results Overview screen "Pending Accept" calibrations are outside of observed ranges but within defined ranges Observed ranges: After 4 calibrations of the same reagent lot and calibrator lot combination, the system calculates observed ranges Defined ranges: The values for Slope, Ratio, Low Cal Deviation and High Cal Deviation entered from the Master Curve card To accept, select the Accept button for that calibration result on the Calibration Data screen After accepting, the calibration status changes to "Valid Operator Accepted" Select Next to continue. Existem vários tipos diferentes de atividades de aquisição disponíveis nos MI Apps. Todas as atividades de aquisição aceitam um estudo e adquirem dados brutos do paciente como uma série para a saída. Os parâmetros podem ser modificados e salvos para protocolos de site específicos. e salvos para protocolos de site específicos. Screens used to review overall calibration status: Calibration Summary - provides calibration status for all tests Reagent Status - lists detailed status information for onboard reagents, including calibration status The overall calibration status messages are: Current Calibration Due to Expire Expired No Calibrator Definition No Master Curve Not Calibrated Waived Check Calibration Status Learn how to check calibration status. Tab TitleTextCalibration Summary Access the Calibration Summary screen by selecting Calibration from the Command Bar, and then selecting the Calibration Summary tab. The Calibration Summary screen displays the Calibration Status of tests. The filter button can be used to limit the display to only tests for reagents that are onboard, or to selected tests.      Reagent Status Access the Reagent Status screen by selecting Reagents from the Command Bar, and then selecting the Status tab. The Reagent Status screen displays information for all of the reagents onboard the system, including the calibration status and calibration expiration date. When complete, select the X in the upper-right corner to close the window and continue.     A atividade de cópia impressa existe em qualquer fluxo de trabalho no qual os dados podem ser impressos ou para criar uma tela que precisa ser salva. A atividade de cópia impressa é usada para salvar áreas de impressão no banco de dados, criar telas que precisam ser salvas, configurar propriedades da área de impressão e gerar saídas de cópias impressas em filme ou papel. Calibrator Definition Cards Located in the calibrator kit Must be scanned with every new calibration lot Can be scanned at any time Must be scanned at the Calibrator Definitions screen Master Curve and Test Definition (MC DEF) Cards Located in the reagent kit Must be scanned with every new reagent lot Can have two or more 2D barcode squares Can only be scanned if the system is in the Ready state Can be scanned from any window location Scanning Calibrator Definition Cards Learn how to scan Calibrator Definition cards. Checklist TitleChecklist TypeChecklist ContentLocate the Calibrator Definition CardHTML The Calibrator Definition card is located in the calibrator kit. It is labeled ADVIA Centaur® Assigned Value Card and has a purple bar at the top. Select each checkbox to learn more about scanning Calibrator Definition cards.    Open the Calibrator Definitions ScreenHTML Select Calibration from the Command Bar, and then select the Calibrator Definitions tab.    Select Add Calibrator DefinitionHTML Select the Add Calibrator Definition button at the bottom of the screen.    Scan the Calibrator Definition CardHTML Scan all of the barcodes on the Calibrator Definition card from top to bottom.    Check the Calibrator ValuesHTML Ensure that the calibrator values are correct. Note: After you select Save, you cannot add or delete a test from a calibrator definition.  Select SaveHTML Select the Save button. When complete, select the X in the upper-right corner to close the window and continue.   Scanning MC DEF cards. Learn how to scan MC DEF cards. Checklist TitleChecklist TypeChecklist ContentLocate the MC DEF CardHTML Locate the MC DEF card in the primary reagent box. Select the ADVIA Centaur® side of the card. Select each checkbox to learn more about scanning MC DEF cards.    Scan the First 2D BarcodeHTML Scan the first 2D barcode on the MC DEF card by placing the card on the barcode reader platform to the right of the touchscreen. Pass the card under the scanner until the blue light points at the center of the 2D barcode. The scanner beeps once and the green light on the scanner flashes once after successfully reading the first 2D barcode. Note: You can also scan the 2D barcode by removing the scanner, holding the MC DEF card and pointing the blue light at the center of the 2D barcode. Scan the Second 2D BarcodeHTML Scan the second 2D barcode. The scanner beeps twice and the green light on the scanner flashes twice after successfully reading the second 2D barcode.     Scan the Remaining 2D Barcodes (if applicable)HTML   Scan the third and fourth 2D barcodes if included on the MCDEF card. The scanner beeps 3 times and 4 times after successfully reading the third and fourth 2D barcodes.     Select SaveHTML Select Save in the confirmation window to save the master curve and test definition and close the window. The master curve will now be listed on the Master Curve Definition screen. When complete, select the X in the upper-right corner to close the window and continue.    Bem-vindo ao curso Online Avançado sobre o syngo® MI Applications. Este material foi desenvolvido como uma continuação do curso básico sobre o syngo MI Applications Basic fornecer mais informações sobre o processamento e as exibições de imagens. Calibrate an assay when:  The calibration interval expires A calibration is invalid A new lot of assay reagent is used Controls are repeatedly out of range Note: Refer to the Instructions for Use (IFU) for calibrator preparation and storage requirements.   Ordering Calibrations Learn how to order a calibration. Instructions:If media does not automatically start, select the play arrow to begin.Flash File:/content/generator/Course_90009702/sim_CXPT_OrderingCalibrators_800x600_9/sim_CXPT_OrderingCalibrators_800x600_9.swfHTML5 File:/content/generator/Course_90009702/sim_CXPT_OrderingCalibrators_800x600_9/index.htmlPDF File: Automatic Calibrations Learn about the option to automatically order calibrations. The system can be configured to automatically create a calibration order when calibration samples are loaded on the system. To configure automatic calibration ordering: Select Setup from the Command Bar Select the System Configuration tab Select System Settings Enable the desired option for Automatic Calibration Order Settings Select Save Automatic Calibration Order Settings options: Current calibration is due to expire or is waived Current calibration is expired or the reagent lot is not calibrated     When complete, select the X in the upper-right corner to close the window and continue. Monitoring Calibration Orders Learn how to monitor calibration orders. Calibration Results Overview screen: To access, select Calibration from the Command Bar, and then select the Calibration Results Overview tab Pending calibration orders will have an Order Status of "New" Inprocess calibration orders will have an Order Status of "Inprocess" and will display a time of completion When complete, select the X in the upper-right corner to close the window and continue.   O syngo é a segunda camada da hierarquia do software da plataforma. Ele é o software comum entre as estações de trabalho das modalidade da Siemens. Nesta seção, vamos nos aprofundar nas principais funções do software syngo dentro do MI Apps. The ADVIA Centaur® XPT system uses a two-point calibration system: Uses low and high calibrators Eliminates the need to measure a full standard curve or calibrate every time the assay is performed Screens used to review calibration data: Calibration Results Overview Calibration Summary Reviewing Calibration Data Learn how to review calibration data. Instructions:If media does not automatically start, select the play arrow to begin.Flash File:/content/generator/Course_90009702/sim_CXPT_ReviewingCalibrationData_800x600_9/sim_CXPT_ReviewingCalibrationData_800x600_9.swfHTML5 File:/content/generator/Course_90009702/sim_CXPT_ReviewingCalibrationData_800x600_9/index.htmlPDF File: Calibration Evaluation Ranges Learn about the calibration evaluation ranges window. Base ImageHotspotsText BlocksImage File The Low and High Cal Deviations are a measure of how well the high and the low calibrator RLUs fit the Master Curve.  Slope is a comparison of high and low calibrator RLUs to the Master Curve. Ratio is a comparison of low and high calibrator RLUs. Calculated CV is the precision of the calibrator replicates based on RLUs. Defined ranges are the values for Slope, Ratio, Low Cal Deviation and High Cal Deviation derived when the MC DEF card is scanned for a specific reagent lot. Since these ranges are reagent lot specific, the relatively narrow limits of the ranges ensure quality calibration monitoring.   Acceptable CV is the maximum CV that is acceptable for a valid calibration. After performing 4 calibrations for a reagent lot and calibrator lot combination, the system calculates Observed Ranges for Slope, Ratio, Low Cal Deviation and High Cal Deviation. When you perform subsequent calibrations using the same reagent lot and calibrator lot combination, the system compares results to the defined ranges from the Master Curve definition and also the observed ranges determined by the system. The system recalculates observed ranges with each valid calibration. Critical Precision determines whether an outlier is too far out to automatically exclude it. O registro de imagem é uma atividade com várias finalidades, usado para preparar dados para exibições sincronizadas ou até mesmo para técnicas mais avançadas, como a mesclagem alfa. Image Registration supports both manual and automatic registration for volume data, including gated and dynamic data.  Utilizing the manual registration, a visual verification and manual interaction is required to ensure that both datasets are properly registered by this activity. O registro de imagem é usado para: executar correção de atenuação preparar um volume de CT para a criação de mapas mu e reutilizar dados para preparação de visualizações em outras estações de trabalho Accepting a Calibration: Required when the calibration status is "Pending Accept" status on the Calibration Results Overview screen "Pending Accept" calibrations are outside of observed ranges but within defined ranges Observed ranges: After 4 calibrations of the same reagent lot and calibrator lot combination, the system calculates observed ranges Defined ranges: The values for Slope, Ratio, Low Cal Deviation and High Cal Deviation entered from the Master Curve card After accepting, the calibration status changes to "Valid Operator Accepted"   Accepting Calibrations Learn how to accept calibrations. Instructions:If media does not automatically start, select the play arrow to begin.Flash File:/content/generator/Course_90009702/sim_CXPT_AcceptingInvalidCalibrations_800x600_9/sim_CXPT_AcceptingInvalidCalibrations_800x600_9.swfHTML5 File:/content/generator/Course_90009702/sim_CXPT_AcceptingInvalidCalibrations_800x600_9/index.htmlPDF File: