ANZAI Load Cell Calibration Video

Magnification Loaded Head Rate Gate Range of Gate output level 000 sec *2.50 x 2.50 Gate 0.01 0 No 10 Resp. CHI: Load CH I : Load CeNl(Stand.rd) Input Position Value Start point Total Time Total Beam Beam Start Total Time Time 10.31 min 40.31 min NO Name Gate Start Start Point Time Position Value : Start point In-peak Start 00000 Position Gate iota' Gate O No ID O No: No ID Please note that the learning material is for training purposes only. In-peak Waveform Setup NO Name Resp. 00000 R•sp. R" Position Head Rate CHI: Load Loaded - Lower Lawer sec 20.01 LOADC€-LL 10101 20.0 20.0 O No ID O NO 10 11.31 min 40.01 min For the proper use of the software or hardware, please always use the Operator Manual or Instructions for Use (hereinafter collectively x 2.50 Siemens Healthineers presents Loaded NO Name Position 000 sec Magnification Magnification < PO "Operator Manual") issued by Siemens Healthineers. This material is to be used as training material only and shall by no means substitute (STANDARD) Resp. Rate Resp. Biograph Horizon 20.0 Repeat procedure for Load CeLL 2.21 min the Operator Manual. Any material used in this training will not be updated on a regular basis and does not necessarily reflect the latest CHI: Load Cell(Standard) HOST COM. Loaded Calibrator Magnification Head Rate Gate version of the software and hardware available at the time of the training. Anzai AZ-733Vl LOADC€-LL Resp. Rate ROS p. Rate x 2.50 x 260 POWER 0.01 min TIGHT, LOADCGLL (STANDARD) (STANDARD) Position Value : min Name P N 00322.5 p, N '00322-5 The Operator Manual shall be used as your main reference, in particular for relevant safety information like warnings and cautions. (STANDARD) Loose 400073-9 SIEMENS Biograph mCT Deep after setting position to +10 Test LOOSE GOOD TIGHT Loose GOOD TIGHT LOADC€-LL Value Please note: Some functions shown in this material are optional and might not be part of your system. Position Load CeLL Calibration TIGHT 50 1.00 N Calibrator Certain products, product related claims or functionalities (hereinafter collectively "Functionality") may not (yet) be commercially available for Loose GOOD TIGHT EXT. 20.0 in your country. Due to regulatory requirements, the future availability of said Functionalities in any specific country is not guaranteed. Healthineers Healthin and magnification to 5.0. Biograph Horizon 1.00 N SIEM-ENS Please contact your local Siemens Healthineers sales representative for the most current information. 403073-9 Calibrator Ca librator Qlibrator Head Rate AVE PET/CT 1.00 N Magnification The reproduction, transmission or distribution of this training or its contents is not permitted without express written authority. Offenders Cancel pread• justment for standarlloadll/l•— will be liable for damages. Justment for Standard {old Manual 3-9 73-9 00073-9 P readjustment for standard Load cell• Biograph Vision Quadra x I. 61 X 1.61 x 1 61 All names and data of patients, parameters and configuration dependent designations are fictional and examples only. for Gate 0.99 N All rights, including rights created by patent grant or registration of a utility model or design, are reserved. Beam @ Siemens Healthcare GmbH 2021 Cancel Beam Preadjustment for Standard Load Cell: position +20, magnification 2.5 Switch Sensor Port to USB mode (switch back after calibration). Place Load Cell on a flat surface (no pressure applied). Remove the weight and put it back on the Load Cell several times, Insert small screwdriver into potentiometer marked with ZERO, Insert screwdriver into potentiometer marked with GA N, Place Load Cell Calibrator Weight on L ad Cell. r Place Load Cell Calibrator Weight on Load Cell. Both Load Cells should be calibrated yearly crewdriver into potentiometer marked with GAIN, crewdr ver into potentiometer marked with.ZERO, wdr er into potentiometer marked with.ZERO, Insert sm • Position • position +20 Beam to assure proper conversion of pressure into electrical signal. turn screwdriver until waveform level is 100. turn screwdriver until waveform level is 100.2 waveform should alternate between O and 100. w vefo saveform should alternate between O and 100.