Atellica® Inventory Manager Cleaning the Printer Job Aid

Cleaning the Printer Job Aid Atellica® Inventory Manager This procedure is for the SATO GL408e printer. CAUTION Do not touch parts inside the printer before letting the printer cool to room temperature. Internal areas of the printer can be hot and cause physical injury. Supplies needed:  Soft cloth or air duster  Isopropyl alcohol  Cotton swab 1. On the printer, press LINE to take the printer offline. The ONLINE LED Indicator will go off and OFFLINE will appear on the display GL408e OFFLINE POWER ON LINE STATUS LABEL RIBBON LINE FRED FUNCTION ENTER CANCEL Published by Siemens Healthcare GmbH © Siemens Healthcare GmbH, 2019 SIEMENS Master Template Effective Date: 3/11/2019 | HOOD05162002998095 Healthineers Job Aid Effective Date: 06/20/2019| HOOD05162002996370 Job Aid | Clean the Printer Effective Date: 06/20/2019 | HOOD05162002996370 2. Turn off the power by pressing the “O” on the power switch WARNING: Do not clean the printer while the printer is connected to a power supply. Disconnect the printer from the power supply and allow the printer to cool to room temperature prior to cleaning. Exercise care when cleaning to prevent personal injury. 08/17/2015 - O 3. Remove the power plug from the back of the printer Published by Siemens Healthcare GmbH © Siemens Healthcare GmbH, 2019 Page 2 of 8 Job Aid | Clean the Printer Effective Date: 06/20/2019 | HOOD05162002996370 4. Open the printer cover. Use a soft cloth to remove any debris from the inside of the printer 5. Move the lavender print head latch all the way to the right to open the print head assembly Published by Siemens Healthcare GmbH © Siemens Healthcare GmbH, 2019 Page 3 of 8 Job Aid | Clean the Printer Effective Date: 06/20/2019 | HOOD05162002996370 6. Remove the label roll and ribbon. These will be reinstalled after completing the cleaning 7. Apply isopropyl alcohol to a clean swab. Gently wipe the entire surface of the print head which is on the underside of the top of the opened print assembly CANCEL Be careful of the cutter edge. Published by Siemens Healthcare GmbH © Siemens Healthcare GmbH, 2019 Page 4 of 8 Job Aid | Clean the Printer Effective Date: 06/20/2019 | HOOD05162002996370 8. Gently wipe the platen roller ENTER CANCEL Be careful of the cutter edge 9. Reinstall the label roll and ribbon. Move the lavender print head latch all the way to the left to close the print head assembly ---- - Published by Siemens Healthcare GmbH © Siemens Healthcare GmbH, 2019 Page 5 of 8 Job Aid | Clean the Printer Effective Date: 06/20/2019 | HOOD05162002996370 10. Insert the power plug into the back of the printer 11. Turn the power on by pressing down on the "I" on the power switch Published by Siemens Healthcare GmbH © Siemens Healthcare GmbH, 2019 Page 6 of 8 Job Aid | Clean the Printer Effective Date: 06/20/2019 | HOOD05162002996370 12. Close the printer cover. Press the LINE button on the front of the printer to bring the printer online GLA06 NATU 10 Published by Siemens Healthcare GmbH © Siemens Healthcare GmbH, 2019 Page 7 of 8 Job Aid | Clean the Printer Effective Date: 06/20/2019 | HOOD05162002996370 Please note that the learning material is for training purposes only! For the proper use of the software or hardware, please always use the Operator Manual or Instructions for Use (hereinafter collectively “Operator Manual”) issued by Siemens Healthineers. This material is to be used as training material only and shall by no means substitute the Operator Manual. Any material used in this training will not be updated on a regular basis and does not necessarily reflect the latest version of the software and hardware available at the time of the training. The Operator's Manual shall be used as your main reference, in particular for relevant safety information like warnings and cautions. Note: Some functions shown in this material are optional and might not be part of your system. Certain products, product related claims or functionalities (hereinafter collectively “Functionality”) may not (yet) be commercially available in your country. Due to regulatory requirements, the future availability of said Functionalities in any specific country is not guaranteed. Please contact your local Siemens Healthineers sales representative for the most current information. The reproduction, transmission or distribution of this training or its contents is not permitted without express written authority. Offenders will be liable for damages. All names and data of patients, parameters and configuration dependent designations are fictional and examples only. All rights, including rights created by patent grant or registration of a utility model or design, are reserved. Atellica is a registered trademark of Siemens Healthcare Diagnostics. Copyright © Siemens Healthcare GmbH 2019 ………………………………………………………… Siemens Healthineers Headquarters Siemens Healthcare GmbH Henkestr. 127 91052 Erlangen, Germany Telephone: +49 9131 84‐0 siemens.com/healthineers Published by Siemens Healthcare GmbH © Siemens Healthcare GmbH, 2019 Page 8 of 8