Elara Max Moving the System Job Aid

Elara Max Moving the System XPRF The following steps will assist with moving the MOBILETT Elara Max. Before transferring the unit to another location, observe the following: • Fold the articulated arm down and secure it with the transport safety lock. NOTE: Do not transfer the Elara Max on surfaces with an incline greater than 7 ft. Turn the system around and drive the unit backwards through doors and tight spaces. • Disconnect the power cable. Briefly pull to trigger the automatic cable rewind. Hold the power plug in one hand while the cable is rewinding. • If using, disconnect the network cable from the wall outlet. Motor Driven Movement: Handle for direction and speed control Safety Switch (back of handle) SIEMENS Unrestricted 0 Published by Siemens Healthcare GmbH © Siemens Healthcare GmbH, 2020 Job Aid Effective Date: 06/11/2020 | HOOD05162003100348 Healthineers Job Aid |Moving The System Effective Date: 06/11/2020 | HOOD05162003100348 • Ensure that the system is powered on when utilizing the motor drive. If motor operation is active, radiation release and detector charging are disabled. • To move the system and to change the direction with motorized support, press the safety switch and start walking forward or backward while holding the drive handle with both hands. Increase the pressure to control the speed of movement. NOTE: If the MOBILETT Elara Max does not move, check whether the device is switched on or charge the batteries if required. Movement Without Motor: • You can move the system even if the motor drive is not available. • Pull the lever on the detector side of the unit. This perma- nently deactivates the automatic brake mechanism so that you can move the device manually. • When the drive is disengaged, the system no longer brakes au- tomatically. Stopping the System: • If movement does not stop, press the emergency STOP button located on the right side of the chassis. • To unlock the emergency button, turn the pressed button clockwise until it snaps back to the normal position. • You can now continue to work as all functions are again active. 105 OBILETT Elara Max SIEMENS Unrestricted 0 Published by Siemens Healthcare GmbH © Siemens Healthcare GmbH, 2020 Job Aid Effective Date: 06/11/2020 | HOOD05162003100348 Healthineers Page 2 of 4 Job Aid |Moving The System Effective Date: 06/11/2020 | HOOD05162003100348 Locking the System: • You can immediately lock the system to prevent unauthorized access to data, drive and current or prior images without having to shut the system down. This allows for work to continue when you are ready to return to the unit. This is done with the below steps. Key Lock Variant (optional): • Turn the key in LOCK position and remove key from lock. OR 2 3 - 5 6 7 8 9 Numeric Lock Variant: • Press lock button on numeric keypad. 0 ED Unlocking the System: • After unlocking the system, the screen and the motor are available again. OR CODE Key Lock Variant: (optional) Insert Key Numeric Lock Variant: Enter 4-digit and turn left to ON position. pin/code. SIEMENS Unrestricted 0 Published by Siemens Healthcare GmbH © Siemens Healthcare GmbH, 2020 Job Aid Effective Date: 06/11/2020 | HOOD05162003100348 Healthineers Page 3 of 4 Job Aid |Moving The System Effective Date: 06/11/2020 | HOOD05162003100348 Please note that the learning material is for training purposes only! For the proper use of the software or hardware, please always use the Operator Manual or Instructions for Use (hereinafter co llectively “Operator Manual”) issued by Siemens Healthineers. This material is to be used as training material only and shall by no means substitute the Operator Manual. Any material used in this training will not be updated on a regular basis and does not necessarily reflect the latest version of the software and hardware available at the time of the training. The Operator's Manual shall be used as your main reference, in particular for relevant safety information like warnings and cau tions. Note: Some functions shown in this material are optional and might not be part of your system. Certain products, product related claims or functionalities (hereinafter collectively “Functionality”) may not (yet) be commercially available in your country. Due to regulatory requirements, the future availability of said Functionalities in any specific country is not guaranteed. Please contact your local Siemens Healthineers sales representative for the most current information. The reproduction, transmission or distribution of this training or its contents is not permitted without express written auth ority. Offenders will be liable for damages. All names and data of patients, parameters and configuration dependent designations are fictional and examples only. All rights, including rights created by patent grant or registration of a utility model or design, are reserved. Copyright © Siemens Healthcare GmbH 2020 Siemens Healthineers Headquarters Siemens Healthcare GmbH Henkestr. 127 91052 Erlangen, Germany Phone: +49 9131 84-0 siemens-healthineers.com SIEMENS Unrestricted 0 Published by Siemens Healthcare GmbH © Siemens Healthcare GmbH, 2020 Job Aid Effective Date: 06/11/2020 | HOOD05162003100348 Healthineers Page 4 of 4