Max Family: Setting up for a Scoliosis/Long Leg Ortho Examination - Video

In this video we will show the steps to correctly set up and perform an orthopedic or ortho study using the Fluoro spot compact FL. See this study can be used for either a spinor long leg exam. This unique option can capture up to four sequential images. The software will then blend the images together, resulting in one uniform image. We will begin by opening the patient exam from either the pre registered patients tab as shown here or by manual entry. After selecting the desired patient, the system will move into the examination tab. Enter the user initials if requested, then select OK. Once in the examination tab, select the eyeglasses icon at the top right of the screen. Then select the desired program, for example. OW long leg if any pop-up boxes display in the bottom right of the FC Fluoro spot compact read an address. The messages, for example, a message may say. Insert the 300 centimeter grid or insert the yd into the wall. Bucky note these messages are not error messages, they are simply instructions to be completed prior to making the exposure. Once the desired patient, an exam are open in the examination tab, it is time to move into the exam room and set up the system. Please note in this video, the detector grid and ortho stand have already been positioned in the room and the tube is set to S ID of 300 centimeters from the wall Bucky. It is recommended to set up the room prior to bringing the patient in for the exam. After the patient is positioned on the ortho stand the table object distance or teody must be measured and entered on the tube touch screen in the Ortho tab. The to D is a measurement from the front of the ortho wall. Stand to the midline of the desired anatomy. Use the dropdown list to input the measurement in centimeters. To set the first ortho position, select the button on the tube for tube angulation, and then angle the tube U utilized the laser light to set the top of the first image. Press the number one button on the touch screen to save this position. Angle the tube down to the lowest position and press the number 2 on the touch screen to save. Note the lanja Tude Inal line of the laser light is utilized for determining both the top and bottom limits of the collimation. During the automated scan. As each limited saved, a check box will appear next to the button on the touch screen. Once positions one and two are set, the system will determine how many images are needed to cover the set distance. In this case, the number 3 indicates 3 images will be made. The system may perform up to four images. When the system is fully set up, hold the acquisition button down during the entire series of exposures. The system will move on its own and acquire the images. When the exam is finished, the tube and detector will move back to a normal working position. If the acquisition button is released prematurely, this series will be aborted and must be repeated in its entire T. All staff should be in the control room area when making the exposure. The FLC will display instructions as the system automatically moves through the series just as it did for the 2E display. This information is displayed in the bottom right corner of the screen. Once the acquisition Button has been pressed, the system moves to the start position, which is the first position of the series. As the system moves through acquiring the images, the display box will show image one of the total number being acquired. In this example, one of three, two of three, and then three of three. Once the last acquisition is made, the system will display a message that the series is complete. At this time, the images will automatically be stitched into one long image and display on the screen.

Patien, Patient 10 • Study Study Tape Device Patient, Name Position Setup • Study Emergency. CHEST PA PA Tape Olss 121212 Emergency. P Name Setup Device Device 121212 Position Patient, Narne Patient, turne cm Cm Patient Patient, Name Patient, Name Patien, Patient, Namne SIEMENS Tape Olss Patient 00131891 Patient, Name 18 cm 18 cm v 13 cm v Patient, Name 83377421 Setup LcngSpne ap 18 cm Device OW LongSpr,e OW LongSpn,e Patien, Locngspnne Patient, turne Patient Patient, Name cm LongSpne OW LongSpne OW LongSplne ap Ov"l LongSp.ne OW LongSpane OW LongSp.ne ap LongSpane ap LongSp.ne ap OW L cngSpne Patient, Name Setup Tape Patient, Narne medium 18 cm i. Position Patien, 18 cm medium Setup Patient, Name 83377421 Patient Patient, Name CW LcngSp:ne ap CW LongSp:ne ap LongS0/ne ap Longsptne ap 18 cm medium cm Locngspne OW LongSpne Longspne Healthineers ' medium LongSpr.e ap medium 18 cm Post.vrocessrg Tape 10 Gene medium PA Device Tape Generator Tape Generator Once images are acquired, Onceimages are acquired, on Tape Generator Generator the system will stitch the - the system will stitch the Tape Generator Measure Generator images together. This process Tape Generator Tape Measure Gen is indicated here on the TUI. Gene tape e Tape Generator Tape re Tape re Image is simulated for demonstration purposes only Measure Gen rape e Gen Gene Tape re Tape re