PEPconnect

MULTIX Impact: FD Calibration Video

This video demonstrates how to perform FD calibration on the MULTIX Impact system.

This video will demonstrate how to perform FD calibration to perform FD calibration. Ensure that you're logged in with the user account which has the FD calibration permission. Then access the service mode of the image station. Move the tube, stand away from the table, top an position the tube pointing towards the floor. Place the detector on the floor in the landscape position. Set the tube to maximum essaidi which should be at least 150 centimeters, but 180 centimeters is recommended. Then use the retractable ruler to measure the set S ID. Be sure to make a note of the ID as it will be needed for calibration. Center the detector in the beam field and collimate the beam field to fully cover the active detector area. Insert the 0.6 millimeter copper filter. Click FD calibration. Please wait a moment while the system verifies the detector parameters and warms up. Enter the measured essaidi in the current value box and click OK. A confirmation dialog appears. Ensure that the 0.6 millimeter copper filter has been inserted and click OK. A confirmation dialog appears. Turn on the calibration switch an click OK to continue. The calibration switch can be found on the backside of the generator on off console. Ensure that nobody is in the examination room and click begin to start automatic. X Ray release. The calibration is then started. Warning, do not turn off the calibration switch when the calibration is in progress. Wait until the calibration is finished. A total of 13 images will be taken and then another confirmation dialog will appear when the calibration is complete. Click OK to save the calibration results. Wait until the calibration results have been saved successfully. A confirmation dialog will appear as an indication that the results have been saved. Then click OK and reboot the entire system to activate the new files. Lastly, it is very important to turn off the calibration switch for normal operation of the system or else radiation is not possible if for some reason the calibration does not succeed, the previous calibration remains valid.

Operation Opefibrmation Opeormation Ionformation Opefirmation Opeibration Calibration Detector Calibration Note: The calibration Examination Service Tool Search Operation Opeibration 25000 nGy 25000 nGy 25000 nGy OGP Editor GP Editor Archiv... FD Calibration PEPconnect RePconnect Search Position Confirmation RIS RIS Snap Shot Statistics Audit Trail Mapping FD Calibration No Refetence imag No Reference image No Refetence image No Refetence image No Reference image No Refetence image No Reference image No Refetence ir Test Image Tube Load Tube L ID Calibration Conditions ms ER 201808080838031M 201808080838031 User setting PIXIUM3543DR 18062G Detector: Serial number: 25000 250000 250000 25000 nGy 250000 Dose 5000 General Properties Processing Exam Site Info. Setting Properties Troperties Properties Processing Troperties Check FD pararneters fM camration Densitivity Density Image DICOM Disc Confibrmation Calfibrmation Instructions: Please assure that no additional objects are in the beam path (e.g. filter)! Please wait while systems verifies Display Config. Troperties Manager No Refetence image No Reference image No Refetence image No Reference image No detector parameters. AEC User Current Focus SID YES NO Put the detector on the floor and tum it to landscape position. Center the detector in beam field and collimate Service 250000 the beam field to fully cover the active detector area. Cu filter O. Omm -1 Please set the tube to maximum SID (at least 150 a-n) and Please set the tube to maximum SID (at least 150 an) and Register Remoster Remoster Register DICOM PMS enter the measured value[cm]. Assistance Access Tube Load Grid Please remove the grid! OK Cancel OK Sensitivity Tem perature NO 27 rc Temperature range Please wait Imin Manager constant Battery Capacity YES Battery capacity bigger than 50% Finished Begin OK Cancel Note: The calibration takes more time to LifeNet complete the 13 Display RIS update all result: Totmal count: Normal count: Failed count: Remove repeat items: co exposures than this Images video illustrates. fi 13% HU 15% HU 12% HU Service switch S3: ON 11/31 Service switch S3: ON 12/31 Service switch S3: ON No acq. IS not ready 11/41 No acq. IS not ready 13/31 No acq. IS not ready 11/31 connector: ON 12/21 mAs connector: ON 12/21 connector: ON 13/31 connector: ON 11/31 connector: ON 12/31 Service mode Il 121 Service mode 1l 1/21 Service mode 12/31 Siemens 11:31 11 11:37:11 11:33:11

  • MULTIX Impact
  • Multix
  • RAD 3
  • Impact
  • Multix
  • Multx
  • Impac
  • MULTIC Impact
  • MULTIX Impact FD calibration
  • FD Calibration
  • Detector Calibration