RAPIDComm® Data Management System Review Results Online Training

Welcome to the RAPIDComm® Data Management System Review Results Online Training course. In this course, you will learn how to review patient and Quality Control (QC) results. Select Next to continue.     Describe how to resend results to the Laboratory Information System (LIS) Describe how to review patient results List the steps to review QC results Upon successful completion of this course, you will be able to: Select Next to continue. Congratulations. You have completed the RAPIDComm® Data Management System Review Results Online Training course. Listed below are the key points that have been presented. Take time to review the material before you proceed to the final quiz. Describe how to review patient results Patient result records: Can be viewed, updated and printed in the Patient Sample Log window Can be reviewed by exception, updated and validated on the Patient Sample Validation List window List the steps to review Quality Control results QC results: Are automatically analyzed to verify they meet acceptance criteria and can be reviewed and printed from the QC Reports window For Blood Gas analyzers can be held for manual analysis based on predefined rules. Manual analysis is performed in the QC Sample Analysis List window Describe how to resend results to the LIS Retransmitting validated patient results to the LIS is: Necessary when the LIS was not functioning properly when the patient samples were being processed Performed from the Patient Sample Log window Select Next to continue. Radial strain is deformation tracking that is assessed perpendicular to the long axis of the heart and perpendicular to the myocardium in the short axis views. Radial strain is like the shortening fraction assessment but taken across the entire myocardium.  Learn more below. Retransmitting validated patient results to the LIS is: Necessary when the LIS was not functioning properly when the patient samples were being processed Performed from the Transfer Log window Retransmit Results to the LIS Learn about resending results to the LIS. Instructions:If media does not automatically start, select the play arrow to begin.Flash File:/content/generator/Course_90010616/sim_RC5_ResendLIS_9_800x600/sim_RC5_ResendLIS_9_800x600.htmHTML5 File:/content/generator/Course_90010616/sim_RC5_ResendLIS_9_800x600/index.htmlPDF File: Po pomyślnym ukończeniu tego kursu będziesz mógł: Wymienić zalety skanowania Dual Energy (DE) Zdefiniować różnice między trybem skanowania TwinSpiral DE, a trybem skanowania TwinBeam DE Poznać podstawowe zasady myExam Compass Wykonać rutynowe skanowanie z wykorzystaniem podwójnej energii Dostosować parametry rekonstrukcji dla skanowania z podwójną energią Patient result records: Can be viewed, updated and printed in the Patient Sample Log window Can be reviewed by exception, updated and validated on the Patient Sample Validation List window Can be reviewed in bulk with reviews recorded electronically Review and Print Patient Results Learn about reviewing and printing patient results. Checklist TitleChecklist TypeChecklist ContentAccess Patient Sample LogHTML On the Reports menu, select Patient Sample Log. Select each checkbox to learn more about reviewing and printing patient results. Select Device TypeHTML Select a device type from the tree in the left pane. Once the device type is selected, device model, location or individual device can also be chosen. Edit Date RangeHTML If necessary edit the date range and select the green arrow. Filter the Sample LogHTML The Patient Sample Log can be filtered as needed to view: Validated samples Validated sample with critical results (Blood Gas only) Validated samples with Mark Positive results (Urinalysis only) Invalid samples Reviewed Status - All, Reviewed or Not Reviewed View a Patient SampleHTML To view or edit a specific patient sample, select the sample and click View. Note that for a Urinalysis or Diabetes samples, double-clicking a sample displays read only details for the sample in a new Results window. Review ResultsHTML Review results on the Validate Patient Sample window. When review is complete, select the Cancel button. For Blood Gas results, reports for individual sample results can be printed allowing critical results to be sent to the appropriate doctor. Print a ReportHTML Reports from the Patient Sample Log window can be printed for blood gas, diabetes and urinalysis results for a specified date range from individual or multiple devices and locations. To print a report, use the navigational tree and specify the date range to display the desired samples. Select the Print button, specify the printer and select OK. Note: Custom reports can be created by selecting the Print Preview button and then selecting the Design Mode icon.   When complete, select the X in the upper-right corner to close the window and continue. Custom Reports Learn more about creating custom reports. Instructions:If media does not automatically start, select the play arrow to begin.Flash File:/content/generator/Course_90010616/sim_RC5_CustomReport2_9_800x470/sim_RC5_CustomReport2_9_800x470.htmHTML5 File:/content/generator/Course_90010616/sim_RC5_CustomReport2_9_800x470/index.htmlPDF File: Manually Validate Patient Results Learn how to view, edit and manually validate patient samples. Checklist TitleChecklist TypeChecklist ContentReview System Alerts ManagerHTML To check for patient samples which require validation, access the System Alerts Manager.  Devices that have samples to be validated will have a red icon next to Patient samples require validation. Select each checkbox to learn more about manually validating results. Validate Blood Gas ResultsSimulationInstructions:If media does not automatically start, select the play arrow to begin.Flash File:/content/generator/Course_90010616/sim_RC_ValSampBG_9_800x492/sim_RC_ValSampBG_9_800x492.swfHTML5 File:/content/generator/Course_90010616/sim_RC_ValSampBG_9_800x492/index.htmlPDF File:Validate UA/Diabetes ResultsSimulationInstructions:If media does not automatically start, select the play arrow to begin.   When complete, select the X in the upper-right corner to close the window and continue.Flash File:/content/generator/Course_90010616/sim_RC_ValSampUA_9_800x492/sim_RC_ValSampUA_9_800x492.swfHTML5 File:/content/generator/Course_90010616/sim_RC_ValSampUA_9_800x492/index.htmlPDF File: Tryb skanowania TwinSpiral Dual Energy CT składa się z dwóch kolejno następujących po sobie skanów spiralnych o różnych wartościach kV i mA. Wysoka wartość kV jest uzyskiwana za pomocą filtra cynowego, który pozwala na separację widma promieniowania. Dwie spirale są połączone automatycznie. Konfiguracja protokołu skanowania i wybór parametrów są tak proste, jak dla każdego standardowego badania z pojedynczą spiralą. TwinSpiral jest bardzo przydatny do charakterystyki materiałów ze względu na wysoką separację widma promieniowania. QC Results: Are transmitted from the POC instruments into RAPIDComm for centralized management Are automatically analyzed to verify they meet acceptance criteria and can be reviewed and printed from the QC Reports window Can be reviewed in bulk with reviews recorded electronically in order to satisfy compliance requirements For Blood Gas analyzers can be held for manual analysis based on predefined rules. Manual analysis is performed in the QC Sample Analysis List window Manually Reviewing Blood Gas QC Results Learn about manually reviewing blood gas QC results. Checklist TitleChecklist TypeChecklist ContentSelect DevicesHTML Blood gas QC results can be diverted for any of the following reasons: Results are missing required information Results cannot be matched with QC material Results include an expired QC material Results meet conditions for user review The sample is a duplicate of a previous sample To view these results, select Devices from the menu bar. Select each checkbox to learn more about manually reviewing blood gas QC results. Select QC Sample AnalysisHTML Select QC Sample Analysis. Select SampleHTML Select a sample from the list in the QC Sample Analysis window and then select the Analyze button. Change StatusHTML The Analyze QC Results window opens. To change the status of the QC sample, select the Status drop-down menu. Select Accepted to include the results in QC statistics, display them in QC charts, and use them to verify QC compliance of subsequent results. Select Rejected to exclude the results from QC statistics and verification of compliance, but display them in QC charts.  Select Discarded to exclude the results from the QC statistics, verification of QC compliance, and QC charts. Enter the Operator IDHTML If necessary, enter the Operator ID. Identify QC MaterialHTML Select the Identify button to choose the appropriate QC material. Add CommentsHTML Comments for QC can be entered in the Comments box or the Select button can be used to choose a predefined comment.  The program will add the date, time, and user to the comment. Select OKHTML   To save any changes made to the Analyze QC Results window, select OK. When complete, select the X in the upper-right corner to close the window and continue. Reviewing QC Results Learn about reviewing QC reports.