MR Radial Hip and Shoulder - Create and Save Protocols - Numaris X

Radial Hip/Shoulder – Create & Save a Protocol – Numaris X Radial Hip/Shoulder – Create & Save a Protocol – Numaris X The Job Aid provides workflow to Create and Save a Radial Hip Protocol for MAGNETOM MR Systems with Numaris X software. 1. Register Patient a. Program Selection > select Hip Protocol I. Complete all mandatory fields b. Select Exam button 2. Exam UI a. Localizer (e.g., AAHip_Scout) I. Select GO – AAHip_Scout Runs b. Add a New Localizer Sequence to Queue I. Double Left Click > Open Localizer II. Select Details View Icon (only if using a Dot Engine Protocol) III. Angle Slices off both Coronal and Axial Images as shown IV. Select GO – Localizer Runs Go First > Angle Localizer as Shown Second > Angle Localizer as Shown Unrestricted 0 Published by Siemens Healthcare GmbH © Siemens Healthcare GmbH, 2020 SIEMENS Master Template Effective Date: 3/5/2020 | HOOD05162003074494 Job Aid Effective Date: 02/02/2021 | HOOD05162003158303 Healthineers Job Aid | MR Radial Hip/Shoulder – Create & Save a Protocol – Numaris X Effective Date: 02/02/2021 | HOOD05162003158303 c. Select and Open a Sequence – to create and position Radial Slices I. Pull Angled Localizer images into GSP Segments – use these images to posi- tion the Radial Slices On II. Select Details View Icon (only if using a Dot Engine Protocol) III. Routine Parameter Card • Change Number of Slices to Equal 1 • Orientation > select Plane to Create Radial Slices • Left Mouse > select Image Segment & Slice > to Create Radial Slices AR & 1:54 min Auto @ 2 @ 0.5x0.5x3.0 mm3 1.00 Routine Contrast Resolution Geometry System Physio Inline Sequence Slice Group 1 FoV Rea 380 mm Slices FoV Phase 75.0 ¢ % Slice Thickness 3.0 4 m Distance Factor 10 ¢ % TR 600.0 ¢ ms Position L14 2 P16 0 H43.5 TE 10.00 - m Orientation Coronal Averages 2 ... Phase Encoding Dir. F>> H Concatenations Phase Oversampling 50 ¢ AutoAlign Hip > Cor L+R Coil Elements BC d. Select Flyout Toolbar + Add Slice 3 Point Stack +/- FOV +1 - Over- Image Ref. Lines Coils Table Line Adj. Group Mode Radial Group Graphics Line Mode Package Mode sampling I. Select Group Graphics Icon Group Graphics II. Select Radial Slices Icon * Radial Slices Unrestricted 0 Published by Siemens Healthcare GmbH © Siemens Healthcare GmbH, 2020 SIEMENS Master Template Effective Date: 3/5/2020 | HOOD05162003074494 Job Aid Effective Date: 02/02/2021 | HOOD05162003158303 Healthineers Page 2 of 4 Job Aid | MR Radial Hip/Shoulder – Create & Save a Protocol – Numaris X Effective Date: 02/02/2021 | HOOD05162003158303 e. Modify Number and Angle of Slice Groups relative to one another I. Depress Left Mouse > Move Mouse Up • Reduces Number of Slice Groups • Increases Angle between Slice Groups • Release Left Mouse – Number and Angle of Slice Groups automatically updated II. Depress Left Mouse > Move Mouse Down • Increases Number of Slice Groups • Reduces Angle between Slice Groups • Release Left Mouse – Number and Angle of Slice Groups automatically updated f. Move Radial Slices Over Joint I. Confirm “Group Graphics” is activated in “Fly Out Toolbar” g. Hint: Select F1 > Rename sequence to “Radial Slices” h. Select GO – Radial Sequence Runs RP Go 3. Select Dot Cockpit Icon a. Select User > Hip Protocol b. Select Edit Icon I. Depress Left Mouse > Drag Localizer Created into Protocol II. Depress Left Mouse > Drag Radial Sequence Created into Protocol c. Select Save Program Icon d. Close Dot Cockpit – Sequences saved to Dot Cockpit Note: To create Radial Slices for a Shoulder Exam repeat the steps above. However, you must angle to the glenoid cartilage. Unrestricted 0 Published by Siemens Healthcare GmbH © Siemens Healthcare GmbH, 2020 SIEMENS Master Template Effective Date: 3/5/2020 | HOOD05162003074494 Job Aid Effective Date: 02/02/2021 | HOOD05162003158303 Healthineers Page 3 of 4 Job Aid | MR Radial Hip/Shoulder – Create & Save a Protocol – Numaris X Effective Date: 02/02/2021 | HOOD05162003158303 Please note that the learning material is for training purposes only! For the proper use of the software or hardware, please always use the Operator Manual or Instructions for Use (hereinafter collectively “Operator Manual”) issued by Siemens Healthineers. This material is to be used as training material only and shall by no means substitute the Operator Manual. Any material used in this training will not be updated on a regular basis and does not necessarily reflect the latest version of the software and hardware available at the time of the training. The Operator's Manual shall be used as your main reference, in particular for relevant safety information like warnings and cautions. Note: Some functions shown in this material are optional and might not be part of your system. Certain products, product related claims or functionalities (hereinafter collectively “Functionality”) may not (yet) be commercially available in your country. Due to regulatory requirements, the future availability of said Functionalities in any specific country is not guaranteed. Please contact your local Siemens Healthineers sales representative for the most current information. The reproduction, transmission or distribution of this training or its contents is not permitted without express written authority. Offenders will be liable for damages. All names and data of patients, parameters and configuration dependent designations are fictional and examples only. All rights, including rights created by patent grant or registration of a utility model or design, are reserved. Copyright © Siemens Healthcare GmbH 2020 Siemens Healthineers Headquarters Siemens Healthcare GmbH Henkestr. 127 91052 Erlangen, Germany Phone: +49 9131 84-0 siemens-healthineers.com Unrestricted 0 Published by Siemens Healthcare GmbH © Siemens Healthcare GmbH, 2020 SIEMENS Master Template Effective Date: 3/5/2020 | HOOD05162003074494 Job Aid Effective Date: 02/02/2021 | HOOD05162003158303 Healthineers Page 4 of 4