SOMATOM go. platform Scan&GO Online Training
Scan&GO Online Training describes the Scan&GO tablet-based mobile workflow.
Upon successful completion of this course you will be able to: Describe the use of the Scan&GO workflow. Describe the tablet's features. Identify the tablet's general screen layout areas. Summarize the steps of the Scan&GO workflow. Perform a routine brain scan and a CT angiography scan. Congratulations. You have completed the SOMATOM go. platform Scan&GO Online Training course. Listed below are the key points that have been presented. Take time to review the material before you proceed to the final quiz. Select the link below to view/print your review material before proceeding to the final quiz. Download and print a copy of the Course Review. Identify the use of the Scan&GO workflow. Scan&GO is a tablet based mobile workflow application. The Scan&GO application enables you to control all routine scan workflows. Without leaving the patient's side you will be able to admit the patient, position the patient for the scan, and finalize the scan with this mobile setup. Describe the tablet's features. The tablet is stored in a cradle on the gantry where it will charge when the system is powered on. The system can only be connected to one tablet. Identify the tablet's general screen layout areas. Patient Data Display - Patient Information display displays patient information on the top, Scheduler icon provides access to the Patient Selection popover. Information Icons Display - Voice control icon and screen active icon. Scan Parameters Display - Displays the protocol name and the patient type as well as patient orientation and scan parameters of the current range. Physiological Data - Displays physiological data such as an electrocardiogram signal, if available. Execution Control Buttons -The execution control provides buttons for controlling the examination workflow. The current workflow step is indicated above the buttons. Tools Area - Enables you to change examination settings and the instruction messages that are displayed. Summarize the steps of the Scan&GO workflow. Patient Selection - Synchronized patient information from the HIS/RIS will be displayed, select the patient to be scanned. Scan Preparation - Properly identify patients and provide them with necessary instructions prior to their scan. Protocol Selection - Select the proper protocol for the patient. Patient Positioning - Move the table and confirm the patient's position on the tablet. Topogram Scan - Activate the topogram scan. Finalizing the Exam - Check the image quality and image reconstruction. Perform a routine brain scan and a CT angiography scan. Adjust topogram length. Adjust the topogram scan range. Instructions to perform the next steps of the scan can be found on the bottom right of the tablet. After reconstructing images, image quality should be reviewed using the scroll bar or the arrows on the right of the reconstructed images. Welcome to the SOMATOM go. platform Scan&GO Online Training. Without leaving the patient's side you will be able to: Admit the Patient Position the Patient Finalize the Patient Scan All Through the Use of the Scan&GO application SOMATOM go. platform scanners feature Scan&GO, a tablet based mobile workflow application. The Scan&GO application enables you to control all routine scan workflows. This Online Training will guide you through the steps of controlling a scan workflow using the Scan&GO application on the tablet and provide you with an opportunity to practice performing scan workflows from the tablet software. The Scan&GO application on the tablet enables you to control scan workflow within the examination room. The tablet is stored in a cradle on the gantry where it will charge when the system is powered on. The system can only be connected to one tablet. Select the links below to learn more about the tablet. General Screen Layout Learn about the tablet's general screen layout. Element HTMLPatient Data DisplayInformation Icons DisplayScan Parameters DisplayPhysiological DataExecution ControlTools Area Sound File Audio ScriptUpon selecting a patient a general screen will be displayed. Its content is described as follows: 1. The patient data display area provides access to the Patient Selection popover, via the Scheduler icon on the left, and displays patient information on the top. The Patient Information display can be selected to toggle between the display of patient specific data and an anonymized "Patient Registered" display. 2. To the right of the patient data display is the information icons display. The two icons displayed here are the voice control which can be selected to enable or disable voice control commands and the screen active icon which will indicate that the display functions are active. 3. The scan parameters display located here displays the protocol name and the patient type as well as patient orientation and scan parameters of the current range. 4. The physiological data will display here only if physiological data, such as an electrocardiogram signal, is available. 5. The execution control buttons located here are used to control the examination workflow. The current workflow step is indicated above the buttons. 6. The tools area is located on the bottom of the screen and enables you to change examination settings and the instruction messages that are displayed including workflow instructions, warnings, and error messages. About the tablet Learn about the tablet's features. Tab TitleTextStoring the Tablet The tablet should be stored in a cradle on the gantry when not in use. Tablet cradles can be found on both sides of the gantry next to the remote scan control cradle.Charging the Tablet The tablet should be charged by placing the tablet in the cradle attached to the gantry. The tablet will only charge when the system is powered on. The mobile workflow that the Scan&GO application supports, allows you to perform scan workflows in the examination room from the tablet without having to use the syngo Acquisition Workplace in the control room. The Scan&GO Approved workflow can vary depending on the type of scan being performed. The learning activity below will demonstrate the workflow of a scan without contrast. Select the link below to learn more about the Scan&GO Approved workflow. Scan&GO Approved Workflow Learn about the Scan&GO Approved Workflow. Checklist TitleChecklist TypeChecklist ContentStep 1-Start ScreenHTML Upon the patient's arrival, a few workflow tasks will need to be performed prior to conducting the scan. Let's review these workflow tasks and please note that all of them can be performed entirely through use of the tablet. You will begin by identifying the patient to be scanned. First, gather the tablet. The No patient registered screen is the first screen that is displayed after launching the Scan&GO examination workflow. Currently, there is no patient registered and no scan protocol selected. (1)Open the Patient Selection screen by tapping GO. Step 2-Patient Selection ScreenHTML Then, you will identify the patient to be scanned from the Patient Selection Screen. On this screen you will see the HIS/RIS Hospital/Radiology Information System (RIS) has synchronized to the tablet displaying the list of patients to be scanned for the day. The patients are listed in chronological order according to their examination time. You can change the list order by tapping on the time, patient name, or requested procedure headlines. From this screen you can: A) Select a registered patient B) Examine an emergency patient C) Return to the start screen by selecting back D) Load the selected patient by tapping GO or tap the corresponding row. E) The Scheduler icon can be selected to go back to the Patient Selection screen Now that you have identified the scheduled patient you will greet the patient. Step 3-Scan PreparationHTML Now that you have identified the scheduled patient from the Patient Selection screen: (1) Greet the patient (2) Utilizing your facilities procedure, identify the patient with two unique patient identifiers (Name and DOB) (3) Provide the patient with any necessary instructions prior to their scan such as, to remove any jewelry, glasses, and prostheses from the body region to be examined (4) Highlight the patient's name by tapping the name from the Patient Selection screen (5) select GO on the bottom right of the screen Step 4-Protocol SelectionHTML Now, that you have selected the scheduled patient from the Patient Selection screen you will continue by selecting the scan protocol. Note, if only one scan protocol is mapped to the requested procedure, the protocol is assigned automatically, the Protocol Selection screen is skipped and you are directed to select patient position. A scan protocol contains predefined scan parameters, reconstruction parameters, and processing parameters for a specific examination. Default Siemens protocols are available for each standard scan workflow: Protocol Selection Screen consists of the following areas: A) Adult protocols (standard, vascular, special protocols) B) Child protocols (standard, vascular, special protocols) C) Patient Model D) Protocol Preview Area E) Symbol identifies scan protocol can be completed with the tablet To select a protocol: (1) Select the corresponding examination icons on the left (Adult or Child) and (standard or vascular) (2) On the patient model, select a body region to be scanned. Upon selection, the body region will be highlighted and the matched protocols are displayed. Note: Special Protocols can also be selected if applicable. (3) Review the content of the protocol descriptions and select the most adequate protocol. (4) Select GO to assign the protocol to the patient. Step 5- Patient PositioningHTML Now, that the protocol has been selected let's position the patient and move the table for the scan: (1)To position the patient on the table: 1a If the table is not in a convenient position for the patient to get on the table, use the RSC and foot to move the table for easer positioning of the patient. 1b Place the patient on the patient table in a comfortable position and iso-center. (2) Move the table to the topogram start position Using the keys on the RSC. There are four keys to move the table horizontally and vertically. (3) Patient Position Selection Confirm the Patient/position on the table matches the patient position that is display in the patient model area. (4) Tap GO to confirm the patient position and display the Ready to load Topogram screen. Step 6-Topogram ScanHTML The Ready to Load Topogram screen appears (1) Activate the topogram scan- by selecting GO from the Ready to load Topogram screen (2) Perform the topogram scan by selecting Start from the RSC or control box. Note: During the acquisition of a topogram you can suspend the scan as soon as the relevant anatomy has been covered by selecting the Suspend key on the RSC or on the control box. Step 7-Tomogram ScanHTML Once the Topogram is acquired the Tomogram planning screen is displayed. A tomogram represents the cross-sectional view of a scanned body region. A tomogram is acquired for diagnostic purposes and is typically based on a preceding topogram scan, which helps you to define the scan range on the body region to be scanned. The tomogram planning screen comprises the following areas. If necessary, the scan range can be adjusted utilizing the following characteristics. If no adjustments are needed, select GO then select Start on the RSC or control box. (A) Scan Direction (B) Exposed area (C) Recon range of a scan range (D) Windowing (E) Repeat Topogram (F) Scan Browser (G) Current Table Position-designated by (H) Lateral Shutter (I) Range Shutter Step 8-Finalizing the ExaminationHTML Now that the scan tasks are complete you can finalize the examination. (1) Check the quality of the acquired tomogram images by utilizing the following features displayed on the screen: Hide Images Icon Slider Bar Arrows Windowing Check&GO button If you are satisfied with the quality of the image, tap Recon All to start the reconstruction. (2) Tap GO to close the patient. (3) Once the required scans are completed, you can unload the patient from the patient table. The Scan&GO workflow supports all routine scans. Now that you have learned the Scan&GO workflow let's practice performing: Head Scan with contrast CT Angiography - Pulmonary Embolism Study Select the links below. Scan&GO Workflow - Pulmonary Embolism Study Learn how to perform a Pulmonary Embolism Study using the Scan&GO workflow. Instructions:Flash File:/content/generator/Course_90018828/2_sim_SOMgo_ScanGoOLT_PulmEmbScan_690x1060_2/2_sim_SOMgo_ScanGoOLT_PulmEmbScan_690x1060_2.swfHTML5 File:/content/generator/Course_90018828/2_sim_SOMgo_ScanGoOLT_PulmEmbScan_690x1060_2/index.htmlPDF File: Scan&GO Workflow - Head Scan Learn how to perform a Head Scan using the Scan&GO workflow. Instructions:Flash File:/content/generator/Course_90018828/1_sim_SOMgo_ScanGoOLT_HeadScan_690x1060/1_sim_SOMgo_ScanGoOLT_HeadScan_690x1060.swfHTML5 File:/content/generator/Course_90018828/1_sim_SOMgo_ScanGoOLT_HeadScan_690x1060/index.htmlPDF File: Please note that the learning material is for training purposes only! For the proper use of the software or hardware, please always use the Operator Manual or Instructions for Use (hereinafter collectively “Operator Manual”) issued by Siemens Healthineers. This material is to be used as training material only and shall by no means substitute the Operator Manual. Any material used in this training will not be updated on a regular basis and does not necessarily reflect the latest version of the software and hardware available at the time of the training. The Operator's Manual shall be used as your main reference, in particular for relevant safety information like warnings and cautions. Note: Some functions shown in this material are optional and might not be part of your system. Certain products, product related claims or functionalities (hereinafter collectively “Functionality”) may not (yet) be commercially available in your country. Due to regulatory requirements, the future availability of said Functionalities in any specific country is not guaranteed. Please contact your local Siemens Healthineers sales representative for the most current information. The reproduction, transmission or distribution of this training or its contents is not permitted without express written authority. Offenders will be liable for damages. All names and data of patients, parameters and configuration dependent designations are fictional and examples only. All rights, including rights created by patent grant or registration of a utility model or design, are reserved. Copyright © Siemens Healthcare GmbH 2018 Please proceed to the final quiz.
- somatom go.
- somatom go
- somatom go.up
- somatom go.now
- somatom go.top
- somatom go.all